Low Voltage Labs Wiki

pitrafficlight_python_example

eric (eric@undisclosed.example.com) — 2023-02-28T13:54:18+00:00

Pi Traffic Light Python Example This is an example of how to use Python to control the LEDs of the Pi Traffic light See the hardware installation page for information on installing the Pi Traffic light on the Raspberry Pi. Software Setup If the Python RPi.GPIO module is not already installed go to

pitrafficlight

eric (eric@undisclosed.example.com) — 2023-02-28T13:54:04+00:00

Pi Traffic Light The Pi-Traffic light provides a fun and easy way to add three 10mm LEDs to your Raspberry Pi project. The red, yellow and green LEDs give visual feedback to the Raspberry Pi GPIO. The Pi-Traffic light can also be used as a tool to learn about controlling the Raspberry Pi GPIO pins.

videooverlayshield

eric (eric@undisclosed.example.com) — 2023-02-28T13:53:52+00:00

VideoOverlayShield The VideoOverlayShield is an Arduino compatible shield board that overlays text on analog video, using the Maxim MAX7456 on-screen display chip. Overview Product information: Documents * Schematic and layout files in gEDA format (zip file):

snowman_kit_build_instructions

eric (eric@undisclosed.example.com) — 2023-02-28T13:53:38+00:00

Snowman Kit Build Instructions Step 1 - Check that all the parts were included with the kit Step 2 - Install the battery holder with the opening to the left Step 3 - Check battery holder orientation Step 4 - Install LEDs D1, D2 and D3 with the longer lead to the positive (+) side

pumpkin_kit_build_instructions

eric (eric@undisclosed.example.com) — 2023-02-28T13:53:22+00:00

Pumpkin Kit Build Instructions Step 1 - Check that all the parts were included with the kit Step 2 - Find the resistor Step 3 - install the resistor into location R1 Step 4 - find the switch Step 5 - Install the switch into location S1

ghost_kit_build_instructions

eric (eric@undisclosed.example.com) — 2023-02-28T13:53:05+00:00

Ghost Kit Build Instructions Step 1 - Check that all the parts were included with the kit Step 2 - Install the battery holder with the opening to the left Step 3 - Check battery holder orientation Step 4 - Install LEDs D1 and D2 with the longer lead to the positive (+) side

flashlight_kit_build_instructions

eric (eric@undisclosed.example.com) — 2023-02-28T13:52:41+00:00

Flashlight Kit Build Instructions Step 1 - Check that all the parts were included with the kit. Step 2 - Install the battery holder with the opening to the left. Step 3 - Install push button S1 into the PCB. Step 4 - Fold the leads of the resistor over before installing into the PCB.

start

eric (eric@undisclosed.example.com) — 2023-02-28T13:52:08+00:00

Low Voltage Labs Wiki Kit Build Instructions ---------- * Flashlight Kit Build Instructions * Ghost Kit Build Instructions * Pumpkin Kit Build Instructions * Snowman Kit Build Instructions Product Documentation ---------- * VideoOverlayShield * PiTrafficLight * PiTrafficLight Python Example

40pin_pi_traffic_installed_alternate.jpg - created

eric (eric@undisclosed.example.com) — 2016-05-27T22:32:39+00:00

40pin_pi_traffic_installed.jpg - created

eric (eric@undisclosed.example.com) — 2016-05-27T22:30:52+00:00

40pin_pi_traffic_line_up_four_pins.jpg - created

eric (eric@undisclosed.example.com) — 2016-05-27T22:26:23+00:00

19107012181_b05441d8f3_b.jpg - created

eric (eric@undisclosed.example.com) — 2016-05-27T22:21:28+00:00

pi_traffic_installed_yellow_led_on.jpg - created

eric (eric@undisclosed.example.com) — 2014-09-27T08:02:13+00:00

pi_traffic_line_up_four_pins.jpg - created

eric (eric@undisclosed.example.com) — 2014-09-27T07:58:45+00:00

wiki:logo.png - created

eric (eric@undisclosed.example.com) — 2013-10-23T06:33:42+00:00